Crux3 Toothpick – X12 Edition | 1-2s 3 Zoll (DIY BUILD KIT)
149,00 €
keine Ausweisung der Mehrwertsteuer gemäß § 19 UStG + Versandkosten
3″ PowerToothpick | Ultra light (35g! dry) | X12 5in1 AIO | Super smooth and powerful 1202.5 UniBell Motors | Caddx Ant 1200TVL FPV Camera
Crux3 Toothpick – X12 Edition | 1-2s 3″ (DIY BUILD KIT)
The popular Crux3 Toothpick – X12 Edition: now with super powerful 1202.5 UniBell motors with 6400kv. The X12 Edition, now with the new X12 5in1 AIO flight controller, which is equipped with OPENVTX (up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD! It comes with SPI ELRS receiver (support ELRS TX module 2.x firmware), and also other RX options like SPI Frsky (support Frsky D8/D16 , REDPINE and SFHSS). In addition, the KIT has been optimized again and makes this special edition even lighter (35g dry!) - a real 3″ ultra-light power quad!
Features
• 35g (dry) 1-2s Toothpick brushless Quad
• UniBell 1202.5 Motoren (6400kv 1-2s) mit 2-Blatt 3″ Props – Powerful and smoothly
• X12 F4 5in1 AIO Flight controller 1-2s Lipo kompatibel
• Caddx Ant 1200TVL FPV Kamera
• Betaflight OSD support ,easy to get RSSI, Voltage, current on your goggles
• Camera Angle adjustable
• Smartaudio ready, change VTX bands, powers, channels via OSD
• Receiver option : ELRS, FrSky, PNP
• Compatible both for 1s-2s Lipo / LIHV
Specifications
• Item Name: Crux3 Toothpick – X12 Edition (DIY BUILD KIT)
• Wheelbase: 115mm
• Size: 97mm x 97mm x 35mm (without propellers)
• Gewicht: ca. 35g (without battery)
• Recommended Battery: 2s 350mah / 400mah / 450mah / 520mah battery
Motoren
• SCHUBKRAFT UniBell 1202.5 KV6400
• Configuration: 9N12P
• Stator Diamter: 12mm
• Stator Length: 2.5mm
• Shaft Diameter: Φ1.5mm
• Motor Dimension(Dia.*Len): Φ14mm*14.5mm
• Weight(g): 4.4g
• No.of Cells(Lipo): 1-2S
Flugcontroller
• Flugcontroller: X12 AIO 5-IN-1 Flight controller built-in 12A ESC and OPENVTX
• Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 12A(each) Blheli_S 4in1 ESC
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G OpenVTX 0mw~400mw
• Built-in ExpressLRS 2.4G,Frsky D8/D16
• Built-in voltage meter sensor , voltage meter scale 110Built-in current meter sensor , current meter scale 470
• VTX antenna: U.FL
• Weight: 5.1g
• Support 1-2S Lipo/ LIHV battery
• Size: 30mm*30mm*8mm (Mount hole size: 25.5mm*25.5mm)
• Betaflight firmware target:
ELRS Version: CRAZYBEEF4SX1280
FRSKY Version:CRAZYBEEF4FR
PNP Version:CRAZYBEEF4DX
LITE Version:CRAZYBEEF4SX1280
ESC
• Power supply: 1-2S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: Z_H_30_REV16_7.HEX
• Default protocol: DSHOT300
• Support Bluejay firmware: When use Blujay firmware with 48khz, should set startup power to 1100/1200
Receiver
Onboard ELRS V2.0 receiver Version
• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : SMD antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8/D16 receiver Version
• SPI BUS receiver
• CC2500 RF
• Compatible Non EU transmitter D8 model Channels: 8ch
• No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support
• Support Frsky D8/ D16 , Redpine , SFHSS
Onboard 5.8g Open VTX
• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v): <650ma (400mw)
• Antenna connector: U.FL
Caddx ANT 1200TVL Kamera (custom)
• Image Sensor: 1/3″ CMOS Sensor
• Horizontal Resolution: 1200 TVL
• TV System: NTSC or PAL
• IMAGE: 4:3
• Synchronization: Internal
• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• S/N Ratio : >52dB (AGC OFF)
• Video Output: CVBSLens: 1.8mm
• Min. Illumination: 0.001Lux@F1.2
• Auto Gain Control: YES
• BLC: YES
• WDR: Global WDR
• DNR: 3D DNR
• Dimensions: 14*14mm(with bracket to 19*19mm)
• Wide Power Input: DC 3.7-18V
• Work Temperature: -20℃~+60℃
• Weight: 2g (N.W.)
Props
• Gemfan 3018-2 (Center Thickness:5.5mmProp Diameter:76.5mm, Center Hole diameter:1.5mm)
Included
• 1x Crux3 Toothpick – X12 Edition (DIY BUILD KIT)
Required
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1s 300mAh Lipo with a high C rate
* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.
| Weight | 0.1 kg |
|---|---|
| Dimensions | 5 × 2 × 1 cm |
| Build-In Empfänger | ELRS, FrSky, PNP |
Be the first to review “Crux3 Toothpick – X12 Edition | 1-2s 3 Zoll (DIY BUILD KIT)”
You must be logged in to post a review.
Related products
Micro Brushless
Microsquad 75mm X2 Pro BLACK EDITION Brushless 2S with built-in Receiver (DIY BUILD KIT)
keine Ausweisung der Mehrwertsteuer gemäß § 19 UStG + Versandkosten
Reviews
There are no reviews yet.