Microsquad Pusher65 – 65mm 1s Pusher Quad (DIY BUILD KIT)
135,00 €
keine Ausweisung der Mehrwertsteuer gemäß § 19 UStG + Versandkosten
65mm 1s Power Pusher Whoop! Super powerful 0802 UniBell motors, X12 5in1 AIO + Runcam Nano3 FPV Cam
Microsquad Pusher65 – 65mm 1s Pusher Quad (DIY BUILD KIT)
The Microsquad Pusher65 – a 65mm 1s Pusher Quad: Super powerful 0802 UniBell motors – optionally with 19000kv or 25000kv deliver the best performance. The X12 5in1 AIO flight controller, which is equipped with OPENVTX (up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD! It comes with SPI ELRS receiver (supports ELRS TX module firmware), and also other RX options like SPI Frsky (support Frsky D8/D16 , REDPINE and SFHSS), Runcam Nano3 (custom edition) and the awesome Microsquad Ultralite Canopy make this Pusher Edition into a real 65mm 1s power pusher quad! Push it!
Features
• 19g (dry) 1s 65mm Brushless Pusher Whoop
• UniBell 0802 Motors (19000kv oder 25000kv 1s) with 2-Blade Gemfan Props – Powerful and smoothly
• X12 F4 5in1 AIO Flight controller
• Runcam Nano3 FPV Camera
• Betaflight OSD support, easy to get RSSI, Voltage, current on your goggles
• Camera Angle adjustable
• Smartaudio ready, change VTX bands, powers, channels via OSD
• Receiver Build-in Option : ELRS, FrSky, PNP
• Compatible for 1s Lipo / LIHV
Specifications
• Item Name: Pusher65 1s Pusher Quad (DIY BUILD KIT) 65mm Brushless FPV drone
• Wheelbase: 65mm
• Gewicht: ca. 19g (without battery)
• Recommended Battery: HV 1S min. 300mah or 380mah, recommend GNB27 Connector + GNB27 Lipos
Motoren
• SCHUBKRAFT UB0802 KV19000 or KV25000
• Shaft: 1mm
• Configuration: 9N12P
• Stator Diameter: 8mm
• Stator Length: 2mm
• Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
• Mounting: M1.4 on Dia 6.6mm
• Plug: Micro JST-1.25 3-pin
• Weight: ca. 1,7g
• Cable: 3cm (without plug)
• Color: red/black
Flugcontroller
• Flugcontroller: X12 AIO 5-IN-1 Flight controller built-in 12A ESC and OPENVTX
• Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 12A(each) Blheli_S 4in1 ESC
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G OpenVTX 0mw~400mw
• Built-in ExpressLRS 2.4G,Frsky D8/D16
• Built-in voltage meter sensor , voltage meter scale 110Built-in current meter sensor , current meter scale 470
• VTX antenna: U.FL
• Weight: 5.1g
• Support 1-2S Lipo/ LIHV battery
• Size: 30mm*30mm*8mm (Mount hole size: 25.5mm*25.5mm)
• Betaflight firmware target:
ELRS Version: CRAZYBEEF4SX1280
FRSKY Version:CRAZYBEEF4FR
PNP Version:CRAZYBEEF4DX
LITE Version:CRAZYBEEF4SX1280
ESC
• Power supply: 1-2S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: Z_H_30_REV16_7.HEX
• Default protocol: DSHOT300
• Support Bluejay firmware: When use Blujay firmware with 48khz, should set startup power to 1100/1200
Receiver
Onboard ELRS V2.0 receiver Version
• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : SMD antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8/D16 receiver Version
• SPI BUS receiver
• CC2500 RF
• Compatible Non EU transmitter D8 model Channels: 8ch
• No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support
• Support Frsky D8/ D16 , Redpine , SFHSS
Onboard 5.8g Open VTX
• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v): <650ma (400mw)
• Antenna connector: U.FL
Runcam Nano3 800tvl Kamera (custom)
• Image Sensor: 1/3″ CMOS
• Horizontal Resolution: 800TVL
• Lens : 2.1mm(M8) FOV 150°
• Signal System: NTSC
• S/N Ratio: >50dB
• Electronic Shutter Speed: Auto
• Auto Gain Control (AGC): Auto
• Min. Illumination: 0.01Lux@1.2F
• D-WDR: Auto
• Day/Night: Color
• Power:DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• Housing Material: ABS
• Net Weight: 1.2g
• Dimensions: L14mm*W14mm*H9mm
Props
• Gemfan 2- blade 31mm / 1mm
Inlcuded
• 1x Microsquad Pusher65 – 1s Pusher Quad (DIY BUILD KIT)
Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1s min. 300mAh or 380mah HV Lipo with a high C rate, as best the GNB27
* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.
| Weight | 0.1 kg |
|---|---|
| Dimensions | 5 × 2 × 1 cm |
| Build-In Empfänger | ELRS, FrSky, PNP (kein Empfänger) |
| KV | 25000kv – Race, 19000kv – FreeStyle |
Be the first to review “Microsquad Pusher65 – 65mm 1s Pusher Quad (DIY BUILD KIT)”
You must be logged in to post a review.
Related products
Micro Brushless
Microsquad BlueSkill 65mm X2 F4 Brushless 2S (16kkv) with built-in Receiver (DIY BUILD KIT)
keine Ausweisung der Mehrwertsteuer gemäß § 19 UStG + Versandkosten
Reviews
There are no reviews yet.