Microsquad Squad62 – Super Tiny 62mm Quad (DIY BUILD KIT)

Microsquad Squad58 – Super Tiny 62mm Quad (DIY BUILD KIT)

And right again! The new Squad62 with only 62mm(!!) nano size and 18g light weight is here! The ultimate 1s sports cannon! The Microsquad Squad62 comes with CrazybeeX AIO 5-in-1 flight controller – build-in VTX, RX, ESC etc., UniBell 0802 motors and Caddx Ant (custom edition) for pin-sharp FPV feeling. The new Microsquad UniBell 0802 engines now with an improved bell and even better performance and power! This 18g hammer part is flown with 1s and also makes a super stylish appearance!

Features
• 18g (dry) 1s 62mm Brushless Quad
• UniBell 0802 Motors (25000kv) with 2-Blade HQ Props – Powerful and smoothly
• CrazybeeX F4 5in1 V2.2 AIO Flight controller 1s Lipo compatible
• Caddx Ant 1200TVL FPV Camera
• Betaflight OSD support, easy to get RSSI, Voltage, current on your goggles
• Camera Angle adjustable
• Smartaudio ready, change VTX bands, powers, channels via OSD
• Receiver option : FrSky, FlySky, PNP
• Compatible for 1s Lipo / LIHV

Flight Controller
• Flugcontroller: CrazybeeX F4 v2.2 Firmware target: CrazybeeF4
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000 (SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G VTX
• Built-in SPI Frsky / Flysky receiver or no receiver
• Built-in 5V 1A BEC

Onboard 4in1 ESC
• MCU upgraded to EFM8BB21
• Power supply: 1S LiPo / LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: S_H_50_REV16_7.HEX
• Default protocol: DSHOT600

Receiver
Onboard Frsky SPI receiver Version
• Compatible with ACCST D8/D16, Recommend D8 mode
• Failsafe support
• No ground interference (Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
• SPI BUS receiver
• Compatible with AFHDS and AFHDS-2A Flysky transmitter
• No ground interference (Transmitter and receiver 1 m from the ground): 200~300m
• Failsafe support

Onboard 5.8g VTX
• Output power: 25mw~200mw switchable
• Frequency: 40CH
• Input voltage: 3.3V~5.5V
• Current consumption: 300mA(type)
• Frequency: 5.8GHz 5bands 40 channels (include Race band)
• Smartaudio ready

Caddx ANT 1200TVL Camera (custom)
• Image Sensor: 1/3″ CMOS Sensor
• Horizontal Resolution: 1200 TVL
• TV System: NTSC or PAL
• IMAGE: 4:3
• Synchronization: Internal
• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• S/N Ratio : >52dB (AGC OFF)
• Video Output: CVBSLens: 1.8mm
• Min. Illumination: 0.001Lux@F1.2
• Auto Gain Control: YES
• BLC: YES
• WDR: Global WDR
• DNR: 3D DNR
• Dimensions: 14*14mm(with bracket to 19*19mm)
• Wide Power Input: DC 3.7-18V
• Work Temperature: -20℃~+60℃
• Weight: 2g (N.W.)

Motors
• SCHUBKRAFT UniBell 0802 KV25000
• Configuration:9N12P
• Stator Diameter: 8mm
• Stator Length: 2mm
• Shaft Diameter: Φ1mm
• Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
• Weight(g):1.7g
• No.of Cells(Lipo):1S

Props
• HQ 31mm 2-Blade – 1mm 

weight (without LiPo) : 18g
weight (with LiPo) : 24g (with GNB 1s HV 250mah Lipo)

Included:
• 1 x Microsquad Squad62 (DIY BUILD KIT)
• 1 x Screwdriver and Proptool

Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1S 250-300mAh Lipo with a high C rate

* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.