Hulky65 – Power Edition (DIY BUILD KIT)

Motors
• SCHUBKRAFT UniBell 0802 KV25000 or 19000KV
• Configuration:9N12P
• Stator Diameter: 8mm
• Stator Length: 2mm
• Shaft Diameter: Φ1mm
• Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
• Weight(g):1.7g
• No.of Cells(Lipo):1S

Flight Controller
• Flugcontroller: Diamond F4 Firmware target: CrazybeeF4
• MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)
• Power: 1S input (DC 2.9-4.35V)
• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in 5.8G Open VTX
• Built-in SPI ELRS, Frsky, FlySky
• Betaflight OSD (SPI Control)
• Built-in 5V 1A BEC
• weight: ca. 3.4g

Onboard 4in1 ESC
• MCU upgraded to EFM8BB21
• Power supply: 1S LiPo/ LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: O_H_5_REV16_8.HEX
• Default protocol: DSHOT600

Receiver
Onboard ELRS V2.0 receiver Version
• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : Enameled copper wire antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8 receiver Version
• SPI BUS receiver Frsky D8 compatible
• Compatible Non EU transmitter D8 Channels: 8ch
• Failsafe support
• No ground interference (Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
• SPI BUS receiver
• Protocol: AFHDS and AFHDS-2A Switchable
• Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
• No ground interference (Transmitter and receiver 1 m from the ground): 200~300m
• Failsafe support

Onboard 5.8g Open VTX
• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v): <650ma (400mw)

Runcam Nano3 800tvl Kamera (custom)
• Image Sensor: 1/3″ CMOS
• Horizontal Resolution: 800TVL
• Lens : 2.1mm(M8) FOV 150°
• Signal System: NTSC
• S/N Ratio: >50dB
• Electronic Shutter Speed: Auto
• Auto Gain Control (AGC): Auto
• Min. Illumination: 0.01Lux@1.2F
• D-WDR: Auto
• Day/Night: Color
• Power:DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• Housing Material: ABS
• Net Weight: 1.2g
• Dimensions: L14mm*W14mm*H9mm

Props
• HQ 31mm 3-Blade or 4-Blade

Included
• 1x Hulky65 – Power Edition (DIY BUILD KIT)

Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1s 300mAh Lipo with a high C rate

* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.