Microsquad Watermelon 75mm X2 F4 Brushless 2S with built-in Receiver (DIY BUILD KIT)

Microsquad Watermelon 75mm X2 F4 Brushless 2S with built-in Receiver (DIY BUILD KIT)

All fans have been waiting for that! The Watermelon Edition now comes with F4 flight control, 0803 engines, super sharp Caddx EOS2 (custom edition), VTX with UFL and the new V3 frame. The new Microsquad 0802 engines now with ball bearings and even better performance and power! Also this 2s Microsquad can be flown with 2s as well as 1s Lipo! That means you can continue to use the 1s Lipos! Thus, you are extremely flexible and can easily adapt your Microsquad to the situation – indoor and outdoor!

Specs
• Flightcontroller: CRAZYBEE F4 PRO FR Firmware target: CrazybeeF4
• MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000 (SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 1-2S battery input (DC 3.5-8.7V)
• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in SPI Frsky, FlySky, DSM2 / DSMX receiver with telemetry
• Built-in Betaflight OSD (SPI Control)
• Built-in Current meter Max 28A
• Current meter scale set to 1175
• Built-in 5V 1A Buck / Boost with LC filter
• Built-in voltage detection
• BLHELI_S pass-through Ready
• Multi Serial port support
• Heading LED Ready
• Weight: ca. 4,2g

ESC
• MCU upgraded to EFM8BB21
• Power supply: 1-2S LiPo / LiPo HV (3.5v / 8.7v)
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: S_H_50_REV16_7.Hex
• Default protocol: Dshot150 / Dshot300 / Dshot600 / Oneshot125 / Multishot / PWM
• Motor plug: JST PH1.25 3-pole

Receiver
• SPI BUS receiver
• Compatible FrSky, FlySky, DSM2 / DSMX
• Channels: 8ch / 16ch (depends on protocol)
• Failsafe support
• No ground interference ( Transmitting and receiving 1 m from the ground): 300m
• *external receiver can also be connected!

Caddx EOS2 Kamera (custom)
• ready with Molex plug for easy VTx plug ’n play
• Input Voltage: 3.3V – 6V
• Camera Resolution: 1200TVL
• Camera Sensor: 1/3 “ CMOS
• Lense: 2.1mm, FOV 160 °
• D-WDR, 2 DNR, 0.001Lux @ F1.2
• Rolling Shutter
• Latency: ca. 3ms
• Video Format: PAL 4:3
• Power: 25mw 300 ~ 350mA bei 5V DCIN
• Size: 14 x 14 x 16.0mm
• Weight: 5g

VTx with 25/200mW* and 40 Kanal (incl. Raceband)
• Input Voltage: 3.3V – 5.5V
• Stromaufnahme: 300mA
• Frequency: 5,8GHz 5 Band 40 Kanal inkl. Raceband
• UFL Antenna
• SmartAudio support
• Weight: ca. 2g (without Antenna)

Motors
• SCHUBKRAFT 0802 KV16000
• Configuration:9N12P
• Stator Diamter: 8mm
• Stator Length: 3mm
• Shaft Diameter: Φ1mm
• Motor Dimension(Dia.*Len):Φ10.5mm*14.5mm
• Weight(g):2.2g
• No.of Cells(Lipo):1S-2S

Props
• Microsquad 40mm Fourblade – Watermelon Edition

Weight (without LiPo) : 32g
Weight (with LiPo) : 44g (with 2 x 250mah Lipo)

Included:
• 1 x SCHUBKRAFT Microsquad Watermelon 75mm X2 F4 Brushless 2S with built-in Receiver (DIY BUILD KIT)
• 1 x USB Charger
• 1 x Screwdriver and Proptool
• 1 x SCHUBKRAFT Stickersheet ( High-tech with transfer sheet)

Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1S 450-550mAh HV Lipo (2x for 2s!) With a high C rate

* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.