Microsquad Squad58 – Super Tiny 58mm Quad (DIY BUILD KIT)
Now it’s really cracking! The new Squad58 with only 58mm(!!) nano size and extremely light weight is here! The ultimate 1s sports cannon! The Microsquad Squad58 comes with Diamond F4 AIO 5-in-1 flight controller – build-in Open VTX, RX, ESC etc., UniBell 0802 motors, Runcam Nano3 (custom edition) and the awesome Microsquad Ultralite Canopy. The new Microsquad UniBell 0802 engines now with an improved bell and even better performance and power! This 14g hammer part is flown with 1s and also makes a super stylish appearance!
Specs
• Flugcontroller: Diamond F4 Firmware target: CrazybeeF4
• MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection)
• Power: 1S input (DC 2.9-4.35V)
• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in 5.8G VTX
• Built-in SPI ELRS, Frsky, FlySky
• Betaflight OSD (SPI Control)
• Built-in 5V 1A BEC
• weight: ca. 3.4g
ESC
• MCU upgraded to EFM8BB21
• Power supply: 1S LiPo/ LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: O_H_5_REV16_8.HEX
• Default protocol: DSHOT600
Receiver
Onboard ELRS V2.0 receiver Version
• Packet Rate option: 50Hz/150Hz/250Hz/500Hz
• ExpressLRS Firmware version: V2.0
• RF Frequency: 2.4GHz
• Antenna : Enameled copper wire antenna
• Telemetry output Power: <12dBm
• Receiver protocol: SPI ExpressLRS
• Compatible with ExpressLRS V2.0 TX Module
• Couldn’t flash separately ExpressLRS firmware
Onboard Frsky SPI D8 receiver Version
• SPI BUS receiver Frsky D8 compatible
• Compatible Non EU transmitter D8 Channels: 8ch
• Failsafe support
• No ground interference (Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
• SPI BUS receiver
• Protocol: AFHDS and AFHDS-2A Switchable
• Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
• No ground interference (Transmitter and receiver 1 m from the ground): 200~300m
• Failsafe support
Onboard 5.8g Open VTX
• Firmware version: OPENVTX
• Smartaudio v2.1
• PIT Mode support
• RCE Mode support
• Channels:48ch
• Transmitting Power: 0/RCE/25mw/100mw/400mw
• Power supply: DC 5V
• Current (5v): <650ma (400mw)
Runcam Nano3 800tvl Kamera (custom)
• Image Sensor: 1/3″ CMOS
• Horizontal Resolution: 800TVL
• Lens : 2.1mm(M8) FOV 150°
• Signal System: NTSC
• S/N Ratio: >50dB
• Electronic Shutter Speed: Auto
• Auto Gain Control (AGC): Auto
• Min. Illumination: 0.01Lux@1.2F
• D-WDR: Auto
• Day/Night: Color
• Power:DC 3-5.5V
• Current: 110mA@5V 120mA@3.3V
• Housing Material: ABS
• Net Weight: 1.2g
• Dimensions: L14mm*W14mm*H9mm
Motors
• SCHUBKRAFT UniBell 0802 KV25000
• Configuration:9N12P
• Stator Diameter: 8mm
• Stator Length: 2mm
• Shaft Diameter: Φ1mm
• Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
• Weight(g):1.7g
• No.of Cells(Lipo):1S
Props
• 40mm 2-Blade – 1mm
weight (without LiPo) : 14g
weight (with LiPo) : 20g (with GNB 1s HV 250mah Lipo)
Included:
• 1 x Microsquad Squad58 (DIY BUILD KIT)
• 1 x USB Charger
• 1 x Screwdriver and Proptool
Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1S 250-300mAh Lipo with a high C rate
* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.
Reviews
There are no reviews yet.