HulkyPro65 X2 – 2s Power Edition (DIY BUILD KIT)

Motoren
• SCHUBKRAFT UB0802 KV14000
• Shaft: 1mm
• Configuration: 9N12P
• Stator Diameter: 8mm
• Stator Length: 2mm
• Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
• Mounting: M1.4 on Dia 6.6mm
• Plug: Micro JST-1.25 3-pin
• Weight: ca. 1,7g
• Cable: 3cm (ohne Stecker)
• Color: rot/schwarz

Flugsteuerung
• Flugcontroller: CrazybeeX F4 v2.2 Firmware target: CrazybeeF4
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000 (SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 1-2S battery input (DC 2.9V-8.7V)
• Built-in 5A (each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G VTX
• Built-in SPI Frsky / Flysky receiver or no receiver
• Built-in 5V 1A BEC

Onboard 4in1 ESC
• MCU upgraded to EFM8BB21
• Power supply: 1-2S LiPo / LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: S_H_50_REV16_7.HEX
• Default protocol: DSHOT600

Empfänger
Onboard Frsky SPI receiver Version
• Compatible with ACCST D8/D16, Recommend D8 mode
• Failsafe support
• No ground interference (Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
• SPI BUS receiver
• Compatible with AFHDS and AFHDS-2A Flysky transmitter
• No ground interference (Transmitter and receiver 1 m from the ground): 200~300m
• Failsafe support

Onboard 5.8g VTX
• Output power: 25mw~200mw switchable
• Frequency: 40CH
• Input voltage: 3.3V~5.5V
• Current consumption: 300mA(type)
• Frequency: 5.8GHz 5bands 40 channels (include Race band)
• Smartaudio ready

Caddx ANT 1200TVL Kamera (custom)
• Image Sensor: 1/3″ CMOS Sensor
• Horizontal Resolution: 1200 TVL
• TV System: NTSC or PAL
• IMAGE: 4:3
• Synchronization: Internal
• Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
• S/N Ratio : >52dB (AGC OFF)
• Video Output: CVBSLens: 1.8mm
• Min. Illumination: 0.001Lux@F1.2
• Auto Gain Control: YES
• BLC: YES
• WDR: Global WDR
• DNR: 3D DNR
• Dimensions: 14*14mm(with bracket to 19*19mm)
• Wide Power Input: DC 3.7-18V
• Work Temperature: -20℃~+60℃
• Weight: 2g (N.W.)

Props
• HQ 4 Blade 31mm / 1mm

Inlcuded
• 1x HulkyPro65 X2 – 2s Power Edition (DIY BUILD KIT)

Required:
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1s 300mAh Lipo with a high C rate

* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.