CrazybeeX F4 V2.2 – 5in1 AIO 1-2s Flight Controller build-in RX + VTX

CrazybeeX F4 V2.2 – 5in1 AIO 1-2s Flight Controller build-in RX + VTX

CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.
It’s a better upgrade flight controller for your whoops. We could use this flight controller to building a 1s-2s compatible lightest 65mm / 75mm / 85mm brushless whoop or 2-3inch ultra light toothpick

Specification
• (Frsky version) CrazybeeX FR version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FR
• (Flysky version) CrazybeeX FS version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FS
• (No RX version) CrazybeeX PNP version: Recommend Betaflight 3.5.7 target CRAZYBEEF4DX
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000(SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 1S-2S battery input (DC 2.9V-8.7V)
• Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
• Built-in Betaflight OSD(SPI Control)
• Built-in 5.8G VTX
• Built-in SPI Frsky receiver support D8/D16
• Built-in 5V 1A BEC
• Built-in voltage detection

Onboard 4in1 ESC
• EFM8BB21
• Power supply: 1-2S LiPo/LiPo HV
• Current: 5A continuous peak 6A (3 seconds)
• Support BLHeliSuite programmable
• Factory firmware: S_H_50_REV16_7.HEX
• Default protocol: DSHOT600

(CrazybeeX FR V2.2 version)
• Onboard Frsky SPI receiver SPI BUS receiver Frsky D8/D16 compatible
• Support Frsky_X_LBT(EU-LBT), Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest)
• Channels: 8ch/16ch
• Failsafe support
• No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
(CrazybeeX FS V2.2 version)
• Onboard Flysky SPI receiver SPI BUS receiver
• Protocol: AFHDS and AFHDS-2A Switchable
• Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
• No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
• Failsafe support
(CrazybeeX PNP V2.2 version W/O on board receiver)
• No onboard SPI receiver

Onboard 5.8g VTX
• Output power: 25mw~200mw switchable
• Frequency: 40CH
• Input voltage: 3.3V 5.5V
• Current consumption: 300mA(type)
• Frequency: 5.8GHz 5bands 40 channels
• With Race band
• Smartaudio ready
• Default vtx_power is 3
• Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground

Onboard Voltage and Current detector
• Voltage Meter scale “110”
• Amperage Mete scale “1175”

CrazybeeX FR V2.2 Bind procedure: Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .

CrazybeeX FS V2.2 Bind procedure: Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.

SPI Receiver option:
• Frsky_D compatible with Frsky D8 protocol
• Frsky_X compatible with Frsky non-eu D16 protocol
• Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
• SFHSS compatible with Futaba S-FHSS protocol
• A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol
• A7105_FLYSKY compatible with Flysky AFHDS protocol

Lieferumfang
1 x CrazybeeX F4 V2.2 – 5in1 AIO 1-2s Flight Controller build-in RX + VTX