{"id":52729,"date":"2022-05-30T16:15:08","date_gmt":"2022-05-30T14:15:08","guid":{"rendered":"https:\/\/micro-squad.com\/?post_type=product&p=52729"},"modified":"2022-05-30T16:28:27","modified_gmt":"2022-05-30T14:28:27","slug":"crazybee-f411-aio-2-4s-flight-controller-build-in-20a-25a-esc-rx","status":"publish","type":"product","link":"https:\/\/micro-squad.com\/en\/product\/crazybee-f411-aio-2-4s-flight-controller-build-in-20a-25a-esc-rx\/","title":{"rendered":"Crazybee F411 AIO 2-4s Flight Controller build-in 20\/25A ESC + RX"},"content":{"rendered":"

<\/span><\/p>\n

\n<\/span><\/p>\n

Crazybee F411 AIO 2-4s Flight Controller build-in 20\/25A ESC + RX<\/strong>
\n<\/span><\/p>\n

CrazyF411 pro is a highly packed 6.3g 2-4S AIO F4 flight controller with built in 20\/25A per channel ESC and diversity receiver.
\nLow latency FrSky D8\/D16 with dual IPEX UFL Antenna (with Power amplifier)
\nLarge soldering pads with 4 angled motor connector (not soldered)
\n2 complete UART (UART 1 with inverted PX pad)
\nCompatible with 110x\/120X\/130X\/140X motors
\nIntegrated with F411 processor, Betaflight OSD, 5V 1.5A BEC<\/p>\n

Specs
\n<\/b><\/p>\n

\u2022 <\/i>Flugcontroller:
\n<\/i><\/strong>\u2022 <\/span>MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
\n\u2022 <\/span>Sensor: MPU-6000 (SPI connection)
\n\u2022 <\/span>Board size: 28.5 * 28.5MM
\n\u2022 <\/span>Power supply: 2-4S battery input (DC 8V-17V)
\n\u2022 <\/span>Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
\n\u2022 <\/span>Built-in Frsky D8\/D16 SPI receiverBuilt-in 2.4G Power Amplification
\n\u2022 <\/span>Built-in Betaflight OSD(SPI Control)
\n\u2022 <\/span>Built-in Current meter
\n\u2022 <\/span>Built-in 5V 1.5A BEC
\n\u2022 <\/span>Built-in voltage detection
\n\u2022 <\/span>Firmware target: MATEKF411RX
\n\u2022 <\/span>Yaw Degrees should set to \u201c-90 degree\u201d to match the flight direction<\/i>
\n<\/i><\/strong><\/p>\n

ESC
\n<\/strong>\u2022 MCU upgraded to EFM8BB21
\n\u2022 Power supply: 2-4S LiPo\/LiPo HV (7v\/17v)
\n\u2022 Current: 20A continuous peak 25A (5 seconds)
\n\u2022 Support BLHeliSuite programmable
\n\u2022 Factory firmware: F_H_40_REV16_7.HEX
\n\u2022 Default protocol: DSHOT600<\/span><\/p>\n

Receiver
\nOnboard Frsky SPI D8\/D16 receiver Version
\n<\/strong>\u2022 SPI BUS receiver
\n\u2022 Frsky D8\/D16 compatibleCompatible Non EU transmitter both D8 mode and D16 mode
\n\u2022 Channels: 8ch\/16chDual antenna
\n\u2022 Failsafe support
\n\u2022 No ground interference ( Transmitter and receiver 1 m from the ground): 400m
\n<\/strong><\/span><\/p>\n

Included<\/strong>
\n1x Crazybee F411 AIO Flight Controller<\/p>\n

<\/span><\/p>\n

 <\/p>\n

Bind procedure:<\/strong>
\nMake the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type \u201cbind_rx_spi\u201d ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is \u201cbind_rx\u201d
\nMake your transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn\u2019t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actual successful , need to go to CLI command and type \u201csave\u201d to finish the binding .<\/p>\n

SPI Receiver option \u2013 all selectable in Betaflight<\/strong>
\nFrsky_D compatible with Frsky D8 protocol
\nFrsky_X compatible with Frsky non-eu D16 protocol
\nFrsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
\nSFHSS compatible with Futaba S-FHSS protocol<\/p>\n

\u00a0<\/span><\/p>\n\t

\n\t\t\t\t\t\t\t\t
\n\t\t\t\"\"\t\t\t\t\t\t\n\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\n