Microsquad Pusher78 HD – DJI Caddx Vista FPV – 78mm 2-3s Pusher Quad (DIY BUILD KIT)

Microsquad Pusher78 HD – DJI Caddx Vista FPV – 78mm 2-3s Pusher Quad (DIY BUILD KIT)

Finally he is here! The Microsquad Pusher78 HD for the DJI / Caddx Vista HD Digital FPV, a light (69g dry) and extremely stable 2-3s HD Pusher Whoop / Quad that can withstand a lot! Pusher78 HD comes with the Crazybee V3 Pro AIO flight controller, 12A ESC (each), super powerful 1202.5(!) UniBell motors with 8000kv, the Gemfan 4-blade props and the Microsquad Pusher78 HD frame (carbon and polycarbon prop guards – super stiff! ). The new Microsquad UniBell engines now with an improved bell and even better performance and power! All that is additionally required here is a Caddx Vista FPV Set and a smaller antenna (than included in the Vista Set) – everything else is already included in this DIY BUILD KIT.

Features
• 69g (dry) 2-3s 78mm HD Brushless FPV Quad
• Carbon Rahmen mit Polycarbonat Propeller Guards
• UniBell 1202.5 Motoren (8000kv) mit 4-Blatt Gemfan Props – Powerful and smoothly
• Crazybee V3 Pro F4 AIO Flight controller 2-3s Lipo kompatibel
• Betaflight OSD support, easy to get RSSI, Voltage, current on your goggles
• Camera Angle adjustable
• Receiver option : FrSky, FlySky, PNP (DJI, ELRS, TBS Crossfire etc.)
• Compatible for 2-3s Lipo / LIHV

Specifications
• Item Name: Microsquad Pusher78 HD – 78mm 2-3s Pusher HD FPV Quad
• Wheelbase: 78mm
• Gewicht: ca. 69g (without battery)
• Recommended Battery: 2S 520mah oder 3s 300mah / 3s 520mah

Flight Control
• (Frsky version) CRAZYBEE F4FR PRO V3.0 Firmware target: CrazybeeF4FR
• (Flysky version) CRAZYBEE F4FS PRO V3.0 Firmware target: CrazybeeF4FS
• (PNP – No RX version) CRAZYBEE F4 PRO V3.0 Firmware target: CrazybeeF4DX
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
• Sensor: MPU-6000(SPI connection)
• Board size: 28.5 * 28.5MM
• Power supply: 2-4S battery input (DC 7-17V)
• Built-in 10A (each) Blheli_S 4in1 ESC Dshot600 ready
• Frsky version Built-in SPI Frsky receiver with telemetry (D8/D16 switchable)
• Flysky version Built-in SPI Flysky receiver with telemetry (AFHDS/AFHDS2A switchable)
• PNP (no RX version need to add external Receiver)
• Built-in Betaflight OSD (SPI Control)
• Built-in Current meter Max 70A
• Current meter scale set to 470
• Built-in 5V 1A BEC
• Built-in voltage detection

Onboard 4in1 ESC
• MCU upgraded to EFM8BB21
• Power supply: 2-4S LiPo/LiPo HV (7v/17v)
• Current: 10A continuous peak 12A (5 seconds)
• Support BLHeliSuite programmable
• Factory firmware: F_H_40_REV16_5.HEX
• Default protocol: DSHOT600

Motors
• Motor: MicroSquad UniBell 1202.5
• KV Optionen: 8000kv
• Configuration:9N12P
• Stator Diamter:12mm
• Stator Length:2.5mm
• Shaft Diameter: Φ1.5mm
• Motor Dimension(Dia.*Len):Φ15mm*15mm
• Weight(g): 4.4g

Props
• Gemfan 40mm 4-Blatt – 1.5mm 

Weight (without battery) : 69g
Weight (with battery) : 98g (with GNB 2s HV 520mah Lipo)

Included
• 1 x Microsquad Pusher78 HD (DIY BUILD KIT)
• 1 x Screwdriver und Proptool

Required:
• Caddx Vista Set and a smaller antenna if you like (other than included in the Caddx Vista Set)
• Transmitter
• The delivery does NOT contain Lipo! We recommend lightweight Microsquad 1S 450-550mAh HV Lipo with a high C rate

* Attention
The video transmitter may spark on non-harmonized frequencies which may not be used in Germany and the EU. § 55 of the Telecommunications Act (TKG) prescribes the following frequencies for use: 5725 to 5875 MHz. The device may only be operated in this frequency range with a power of 25mW. The use of unauthorized frequencies and higher performance constitutes a misdemeanor. In the delivery state the device is in DE and EU allowed 5740 MHz (band F, channel 1) with a power of 25mW.